Metal Study guides, Class notes & Summaries

Metal Coils Endorsement (NYS) Exam Questions with Answers (Latest Update 2024)

What does GMAW stand for - Answer-Gas Metal Arc Welding GMAW is generally done with what polarity? - Answer-Direct current electrode positive (DC+) What type of power source is generally used for GMAW welding - Answer-Constant Voltage What does E stand for in ER70S-6 - Answer-electrode What does "70" stand for in ER70S-3? - Answer-tensile strength What mode of metal transfer allows for only flat/horizontal position GMAW welding - Answer-Spray What gas mixture is generally associated with...

Type ____ is multiconductor cable identified for use as underground service entrance cable. correct answer: Type USE cable Knife switch rated for more than 1200 Amps at 250Volts or less correct answer: Can be used only as isolating switch, shall not be opened under load Track lighting with outlets in a bathroom is not allowed because ? correct answer: Track lighting has receptacle Where internal combustion engines are used as the prime motor, an on site fuel supply shall be provided ...

CWB Level 3 Module 24 Basic Metallurgy and Welding Metallurgy of Aluminum Questions & Answers 2023 ( A+ GRADED 100% VERIFIED)

Module 29105-15 Base Metal Preparation (19-20).fires Most work site ___________ related to welding operations are caused by cutting torches. strong The more carbon content steel has, the more ____________ the steel becomes. austenitic A term that refers to a type of metal stainless steel group, which is most often encountered by welders. chromium Common-grade stainless steels normally contain at least 11 percent _________________. classified Grain structures are the way ...

What is the result if the neutral wire becomes open on a multiwire circuit having unequal loads? Select one: a. The load of higher resistance would overheat and probably be damaged. b. The load of lesser resistance would overheat and probably be damaged. c. No effect until one load is turned off or opens. d. No effect. The load of higher resistance would overheat and probably be damaged. Refer to Figure 128.202. ___ volts are applied across the water heater element. S...

1. What can cause stress risers? a. punch marks b. corrosion grooves c. corrosion pits d. all of the above - Answer- D 2. When a metal (or alloy) cools from a liquid to a solid state, the lack of molten metal to feed the shrinkage will lead to: a. pipes, voids and cavities b. sponge like appearance and hot tears c. none of the above d. both a and b - Answer- D 2. Which of the following is not a cause of undercutting? a. excessive amperage b. excessive travel speed c. exces...

INC3701 Assignment 2 (COMPLETE ANSWERS) 2024 (688449) - DUE 21 May 2024 ;100 % TRUSTED workings, explanations and solutions. For assistance call or W.h.a.t.s.a.p.p us on ...(.+.2.5.4.7.7.9.5.4.0.1.3.2)........... Assignment 02 Inclusive Education: Generic Module Module code: INC3701 Year module Department of Inclusive Education 1 Open Rubric This tutorial letter contains important information about the module. BARCODE INC3701/103/2024 2 Academic dishonesty Assignment 2 ...

Nicet Level 1 - Water Based Layout Practice Questions and Answers 100% Pass Toggle hangers shall be permitted only for the support of pipe __________ inches or smaller in size under ceilings of hollow tile or metal lath and plaster. - Answer-1 2/2 in. (ref. NFPA 13 2016 Sec. 9.2.1.1.2. While conducting a flow test, the chosen hydrant should be ______ - Answer-As close to the property where the sprinkler system is being installed. (Ref, NFPA 13 Sec. A.24.2.2. or NFPA 291) What formula is ...