In a series circuit Study guides, Class notes & Summaries

NEIEP 700 Final Exam Version 2 (Latest 2023/ 2024 Update) Questions and Verified Answers| 100% Correct| Grade A Q: What is the primary reason AC relays hum or chatter? Answer: AC cycle reversal Q: Which of the following best describes the contact rating of a magnetic switch? Answer: The maximum voltage and current that can be safely interrupted Q: How can you reduce contact arcing on plug-in relay contacts? Answer: Wire two contacts of the same relay in series ...

Traffic Signal Technician Level II (Latest 2024 / 2025 Update) Questions and Verified Answers | Grade A | 100% Correct Q: Check for proper operating DC voltage, check for the absence of red on a phase that does not have green, yellow, or walk, check on a simultaneous are functions that are provided by both - Answer: CMU and MMU Q: What is the purpose of relays in a traffic signal system? Answer: to transfer the outputs from one component to another Q: What device minimizes the amount of voltage ...

Level 2 Module 1 Alternating Currents 2:1 What is the step-down turns ratio of a transformer with 200 turns in the primary and 100 turns in the secondary? induced high voltage Opening the secondary of a CT under load will cause a dangerous level of___. 40Hz What is the hertz rating of an AC circuit if the frequency is 20 cycles per 1/2 second? 340V Given: A circuit has an rms voltage of 120VAC. What is the peak-to-peak voltage? 175V A circuit has a peak voltage of 275V....

When connecting a 3-phase motor the three lines (T1,T2 and T3) are usually connected to __________. - L1, L2, and L3 Electricians use __________ to prevent damage to electrical wiring running to the machine. - rigid and flexible conduit When the wire or foil strip inside a fuse melts, the fuse is said to be __________. - blown The difference between a fuse and a circuit breaker is __________. - circuit breakers can be reset and used again The amount two electrical...

Associate CET 6th Guide Latest 2024 Solved Correctly Questions With Solutions.

NEIEP 300 2023 Exam Questions and Correct Answers How should ammeters be used to take measurements in a circuit - ANSWER Connected in series with the circuit What will happen to the current in a circuit if the resistance is doubled - ANSWER Current will be halved How do you measure voltage in a circuit - ANSWER Meter must be parallel with volt being measured What is the outermost shell of an atom called - ANSWER Valence shell The Nucleus of...

NETA Level II Exam Questions Correctly Answered 2024.What is the preferred method of performing primary-injection testing on a low voltage circuit breaker with ground fault protection? Use of the manufacturer's test kit or rewiring the neutral CT input is the preferred method of primary-injection testing on a low voltage circuit breaker with ground fault protection, otherwise two poles can be connected in series to provide balanced secondary currents to the trip unit. At what current le...

After installing a new battery how long should you wait to allow for pcm time no need to wait As blower motor speed decreases the voltage drop across the resistance block.... increases What should you do first when replacing junction block or fuse? Unlock the battery ground cable The polarity of the voltage applied to the electromagnetic coils of an actual working DC motor is.... a commutator When performing a volt drop test the volt meter setting should be set to...

ATT Test 2 Questions and Answers Latest Updated 2023 Definition of series circuit Current flows in a single path through all components In which direction does current flow? Negative to positive Current is the ____ throughout whole circuit Same 4 steps of troubleshooting Analyze, check setup, calculate/measure, check results An open series component drops _____ volts Applied Resistance is how much over open component? Max or infinite Short provide...

Fire Investigator TCFP Exam| 500+ Practice Questions and Verified Answers| 2023/ 2024 Update Q: What is the ability of a structural assembly to maintain its load-bearing capacity and structural integrity under fire conditions Answer: A.) Fire resistance Q: What would most likely need to happen for the fuel-gas product to ignite in the piping system Answer: C.) Leak from the system Q: What can the fire investigator conclude when the electrical safety devices operated ...