Exam (elaborations)
NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS GRADED A+
- Course
- Institution
NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS GRADED A+
[Show more]
1 review
By: alexanderjoubert88 • 9 months ago
Content preview
NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS GRADED A+Dew point is the temperature at which - Answer condensation occurs.
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining. Your FIRST preferred course of action is to: - Answer Document the problem and advise the Contractor and Owner's representative.
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a - Answer blotter test for the presence of oil and water.
Upon arrival of coating materials, the inspector should - Answer observe and document the amount of material and batch numbers.
Relative humidity is - Answer a measure of the amount of moisture in the air compared to saturation level.
Galvanic corrosion occurs on which of the following substrates? - Answer Metal
When applying Thermal Spray Coatings the specification is most likely to reference: -
Answer SSPC-CS 23.00/AWS C2.23/NACE No. 12
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial type magnetic pull off Dry Film Thickness(DFT) gauge? - Answer 2.5 cm (1 inch)
Polymerization is the process of? - Answer Monomers joining together.
An exposed area of the substrate or previous coat of a conductive material, often caused by poor application technique is called: - Answer Holiday
Checking is: - Answer a fine crack in the surface of a coating that rarely reaches the substrate.
Inspection documentation is important because: - Answer Owners use the documentation for a variety of purposes.
An Inspectors personal log book should contain: - Answer No comments regarding the application team.
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors. Your FIRST preferred course of action is to: - Answer Review the NACE Attestation prior to making a decision. NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS GRADED A+
Good record can provide maintenance departments with detailed information about ALL of the following EXCEPT: - Answer How the item was coated.
Non Conformance Reports are completed by the Inspector: - Answer When the Inspector and Contractor deem it to be significant non conforming item.
The initial steel condition is important to the NACE Inspector because: - Answer The Inspector may have to reject the steel.
The form of corrosion that has the largest potential for unexpected catastrophic failure is: - Answer Galvanic Corrosion
What is used to determine compressed air cleanliness? - Answer Profilometer
Osmotic blistering is most likely to occur as a result of: - Answer Airless spray application.
When performing tests for oil and grease using an ultra violet light, the NACE Inspector should be aware that: - Answer Synthetic oil or grease may not be identified.
To achieve consistently accurate results with ALL alt test equipment: - Answer wash your hands before sampling.
When holiday testing is required the Inspector is always required to enforce what standard? - Answer NACE SP 0188
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the
default restriction level is: - Answer Level 3
Fine cracks in the surface of a coating that rarely reach the substrate are called: - Answer Checking
It is good practice for the NACE Inspector to have instrument calibration certificates available: - Answer At all times.
In a non convertible coating the role of the primary solvent is to: - Answer To control the evaporation rate.
Removal of weld splatter is required: - Answer When specifically identified in the owners specification.
Common errors that may produce inaccurate readings when using a Dial Type Magnetic Pull Off Dry Film Thickness(DFT) gauge include: - Answer Failing to determine the Base Metal Reading(BMR),Rotating the dial too fast when taking measurements, and Measuring ditty, tacky, or soft films.
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller EvaTee. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $13.49. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
73773 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now