What is the asme - Study guides, Class notes & Summaries

MASS 2A-1C Hoisting Exam Questions With Verified Answers How many pounds in a ton? - answer2000 pounds What type of equipment requires a H/H license in Mass? - answer10 feet or either, 1/4 cu/yd 500 pounds What type of system is used when working on de-energized circuitry? - answerLock out/Tag out All welding and cutting on hoisting equipment must be done in accordance with what code? - answer1998 ASME Chapter IX What type of protection is required for hoisting operation? - answerROPS, ...

Module 29105-15 Base Metal Preparation (19-20).fires Most work site ___________ related to welding operations are caused by cutting torches. strong The more carbon content steel has, the more ____________ the steel becomes. austenitic A term that refers to a type of metal stainless steel group, which is most often encountered by welders. chromium Common-grade stainless steels normally contain at least 11 percent _________________. classified Grain structures are the way ...

NEIEP 200 Final VERIFIED100% SOLUTIONS 2023//2024 Which lay of wire rope has the strand wires in line with the rope axis? - ANSWER Regular Lay At what speed should the counterweight safeties be set to trip? - ANSWER Up to 10% higher than the car governor Which type of safety uses an oil buffer between the car and safety planks? - ANSWER Type C What is the purpose of the terminal motion switch? - ANSWER slow down and stop the car automatically at or near the top or bottom landin...

NCCCO Tower Crane Exam (2024 / 2025) Questions and 100% Correct Verified Answers | Grade A Q: According to OSHA when lifting personnel the cranes hook must be the type that Answer: Can be closed and locked Q: According to OSHA when working over water with a man basket are the people inside required to wear a belt/harness? Answer: No harness or belt required Q: According to ASME B30.3 when working near powerlines where should caution stickers be installed? Answer: Operator station and at the base...

ASME - Answer-American Society of Mechanical Engineers DOSH - Answer-Division of Occupational Safety and Health LADBS - Answer-Los Angeles Department of Building and Safety Alteration made to conveyance shall comply with ASME A17.1-204 Section - Answer-8.7 The seismic section of ASME A17.1-2004 and alterations made to conveyances must also comply with this section - Answer-8.4 What must be submitted to the applicable Division Elevator office prior to beginning construction or alterations ...

High pressure boiler exam NYC License 2024 Questions and Answers Latent Heat of Vaporization - CORRECT ANSWER-970.3 Btu's Meaning of BTU - CORRECT ANSWER-British Thermal Unit At what PSI can the vent valve be closed when refilling a boiler - CORRECT ANSWER25 PSI What kind of Air controls combustion efficiency? - CORRECT ANSWER-Secondary Air Boiler main steam stop valves should be ____ valves. - CORRECT ANSWER-OSandY gate valves Forced draft and Induced draft are what kinds of draft - ...

for the purpose of rating boiler horsepower for an Engineers licence only, how many square feet of boiler surface shall be equivalent to one boiler horsepower on a boiler? correct answer: 10 Sq. Ft. Heating Surface What is meant by the term Low Pressure Boiler? correct answer: boilers operating at a steam or other vapor pressure of 15 psig. or less, or a hot water or other liquid boiler in which the pressure does not exceed 160 psig. Or a temperature of 250 f°. A person holding a curren...

API 570 - Open Book - Practice Exam 2024 Already Passed A Hydrotest is conducted on an underground line as a substitute for the external inspection. The test pressure is 200 Psig. At the end of the test, the pressure must be at least - API 570 9.8.6 190 Psig. Determine the maximum allowed pressure for a Class 300 flange that has a design temperature of 950 °F. The flange material is ASTM A217 Gr. C12 - B16.5 Table 1.1-1 375 Psig. An 8 NPS pipe is being replaced with A106 gr. B mater...

A Hydrotest is conducted on an underground line as a substitute for the external inspection. The test pressure is 200 Psig. At the end of the test, the pressure must be at least - API 570 9.8.6 190 Psig. Determine the maximum allowed pressure for a Class 300 flange that has a design temperature of 950 °F. The flange material is ASTM A217 Gr. C12 - B16.5 Table 1.1-1 375 Psig. An 8 NPS pipe is being replaced with A106 gr. B material. The pipe retirement thickness (Tmin) is 0.218" and the ...

If load is undetermined who is to find out if load weight does not exceed crane rating at radius at which the load is to be lifted - ANSWER Person responsible for lift Where should climbing instructions be kept - ANSWER ON Site All climbing operations shall be performed under the supervision of - ANSWER Qualified person When cranes are erected, load limiting devices shall be tested for proper setting and operation - ANSWER Before crane is placed in service Hooks shall be equipped with lat...